Total Files over 1GB

chienpin · 6th August 2003, 14:31

If Total File Over 1GB...
How can i do...
Who can give my some sample...
Thanks!!

Afrow UK · 6th August 2003, 14:39

You want to compress a 1gb file into the installer?
That can be done yes.

Just use:

code:
Section "Install main file"

SetOutPath "$INSTDIR"

 File "C:\1gb-file.ext" ;to be compressed and extracted to $INSTDIR

SectionEnd

-Stu

Joost Verburg · 6th August 2003, 15:05

If have problems with the compilation of large files, see
http://nsis.sourceforge.net/site/ind...&tx_faq_faq=15

Afrow UK · 6th August 2003, 16:20

Nice new website

GJ!!!

-Stu

chienpin · 7th August 2003, 01:37

Sorry~~~
I want
disk1 500MB...
disk2 500MB...

Sunjammer · 7th August 2003, 06:50

There is no automatic disk spanning in NSIS (yes it has been requested before) so you'd have to achieve this by:

NSIS installer on disk 1, files on disk 1 and disk 2, use CopyFiles to install them from the install disks to the user disk.
NSIS installer on disk 1 including the disk 1 files using File, files on disk 2 should be installed using CopyFiles.
Two NSIS installers, one one disk 1 and one on disk 2, use the File command to pack the files into the installers, installer 1 runs installer 2 after first requesting a disk change (if necessary).

Note: For all suggestions YOU are responsible for deciding which files go on disk 1 and which files go on disk 2.

Disk spanning has been discussed many times on this forum before, I suggest you search for more information. No doubt others will post with more suggestions for you here too!

6th August 2003, 14:31	#1
chienpin Junior Member Join Date: Mar 2003 Posts: 4	Total Files over 1GB If Total File Over 1GB... How can i do... Who can give my some sample... Thanks!!

6th August 2003, 14:39	#2
Afrow UK Moderator Join Date: Nov 2002 Location: Surrey, England Posts: 8,434	You want to compress a 1gb file into the installer? That can be done yes. Just use: code: Section "Install main file" SetOutPath "$INSTDIR" File "C:\1gb-file.ext" ;to be compressed and extracted to $INSTDIR SectionEnd -Stu

7th August 2003, 06:50	#6
Sunjammer Major Dude Join Date: Jun 2002 Location: Swindon, UK Posts: 559	There is no automatic disk spanning in NSIS (yes it has been requested before) so you'd have to achieve this by: NSIS installer on disk 1, files on disk 1 and disk 2, use CopyFiles to install them from the install disks to the user disk. NSIS installer on disk 1 including the disk 1 files using File, files on disk 2 should be installed using CopyFiles. Two NSIS installers, one one disk 1 and one on disk 2, use the File command to pack the files into the installers, installer 1 runs installer 2 after first requesting a disk change (if necessary). Note: For all suggestions YOU are responsible for deciding which files go on disk 1 and which files go on disk 2. Disk spanning has been discussed many times on this forum before, I suggest you search for more information. No doubt others will post with more suggestions for you here too!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

6th August 2003, 15:05	#3
Joost Verburg NSIS MUI Dev Join Date: Nov 2001 Posts: 3,717	If have problems with the compilation of large files, see http://nsis.sourceforge.net/site/ind...&tx_faq_faq=15

6th August 2003, 16:20	#4
Afrow UK Moderator Join Date: Nov 2002 Location: Surrey, England Posts: 8,434	Nice new website GJ!!! -Stu

7th August 2003, 01:37	#5
chienpin Junior Member Join Date: Mar 2003 Posts: 4	Sorry~~~ I want disk1 500MB... disk2 500MB...